How to Fly a Helicopter in MSFS 2024
|
|
Learning how to fly a helicopter in MSFS 2024 comes down to one skill: making small inputs, then waiting to see what they do. A helicopter won't look after itself the way an aeroplane will, and every change on one control affects the others. This guide takes you from your first lift-off to your first controlled landing, in the order that makes each step easier. Most people need several short sessions to get a stable hover, so don't judge yourself on the first attempt.
You can start with a joystick, but analogue axes matter far more than buttons. A helicopter needs smooth, continuous input on three controls at once:
Pick a simple aircraft as well. The Robinson R66 and the Guimbal Cabri G2 are common starting points in MSFS 2024, and calm weather on a wide, flat runway gives you room to make mistakes. If you're new to flight sim hardware, our guide to your first month with flight sim controls covers the basics of sensitivity and dead zones.
Open Assistance Options and find the piloting settings. MSFS 2024 includes helpers for the tail rotor and the cyclic, plus protection against vortex ring state. Leave them all on while you learn. Remove the tail rotor help first, once you can hold a steady hover for about a minute, and leave the cyclic help until last.
In the control settings, search for cyclic and assign your stick's pitch and roll axes. Then assign your collective axis and your pedals or twist axis. Clear any aeroplane commands sitting on the same axes, because a conflict here is the most common cause of strange behaviour. Check that lowering your lever gives you minimum collective, and reverse the axis if it doesn't.
The cyclic is very sensitive around the centre, so many pilots add a softer response curve. A setting of around -30% to -40% on the cyclic and pedal axes is a common starting point, with little or no dead zone. Adjust it to suit your hardware.
Skip the full start-up procedure for now and begin on the runway with the engine running. Centre your cyclic, set your pedals to neutral and keep the collective fully down. You can learn the aircraft's checklist once hovering feels manageable.
A hover is the foundation of helicopter flying, and it's where most of your practice should go. Pick a fixed point several metres ahead of you rather than looking straight down, then raise the collective very slowly.
As the skids get light, the nose will try to swing. On a counter-clockwise rotor such as the R66 or Bell 407, adding power needs left pedal. On a clockwise rotor such as the H125 or Cabri G2, it needs right pedal. Lift to just a few feet, then use the cyclic for drift, the collective for height and the pedals for heading.
Make one small input, wait, then correct again. Most runaway oscillations come from correcting too late and too hard. A good first target is staying within a 20-metre circle for 30 seconds. If the movement keeps growing, land and start again.
From a steady hover, ease the cyclic forward and add a little collective as you start to move, otherwise the helicopter will sink. At around 16 to 24 knots you'll reach effective translational lift, when the rotor gets cleaner air and produces more lift. You'll feel a brief vibration and the nose will want to rise, so hold it with gentle forward cyclic and let the climb begin.
Climb to 500 to 1,000 feet and settle into forward flight. In the R66, 100 to 110 knots is a typical cruise. Use the aircraft's trim to take the load off the cyclic, and practise gentle turns and small height changes before you try a landing.
Set up a long, shallow approach instead of descending steeply. For a light helicopter in calm air, about 40 to 60 knots and no more than 500 feet per minute is a sensible starting point. Slow down with gentle aft cyclic, adjusting the collective to hold your descent path.
You'll lose translational lift as you slow through about 25 knots, so expect the helicopter to feel softer and to need more pedal. Bring it to a walking pace and into a brief hover above your landing spot. Then lower the collective gently, keep correcting drift and yaw, and only lower it fully once the skids are carrying the weight.
The main rotor turns one way, so the fuselage wants to turn the other way, and the tail rotor counters that force. Every collective change alters the torque, which means your feet are working constantly in a hover. A twist axis will get you flying, but separate pedals let you hold a heading while your hands manage the cyclic and collective. You'll find the wider range in our rudder pedals and helicopter controls collections.
The Honeycomb Charlie Rudder Pedals suit pilots who split their time between aeroplanes and helicopters, with adjustable tension to help you tune the feel.
If helicopters are your main focus, the Max Flight Stick Anti-Torque Pedals are built specifically for rotorcraft, with damped pistons that help with the small corrections you make in a hover.
Yes, at first. Hovering is the hardest part because you're managing three controls at once. The assists make it far easier to start, and short, regular practice sessions work better than one long session.
The Robinson R66 and Guimbal Cabri G2 are the usual choices. The Cabri G2 is a small trainer and can feel quite sensitive. Choose one and stick with it while you learn to hover.
The nose usually swings because the pedal input doesn't match the collective. If it spins with no way to stop it, check that your pedal or twist axis is bound, isn't reversed and isn't clashing with another command.
Yes. A twist axis on your joystick works, and the tail rotor assist can handle much of the work while you learn. Pedals become more useful once you turn that assist off.
Vortex ring state happens when a helicopter descends into its own downwash and loses lift. It's most likely in a descent of around 300 feet per minute or more below about 15 to 25 knots. To recover, lower the collective slightly and use the cyclic to move forward or sideways into clean air.
Once your hover feels steady, the rest of helicopter flying gets much easier, so keep coming back to it. If you're looking for somewhere new to fly, our list of the best flight simulator games is a good next stop. When you're ready to add hardware, Gamer Gear Direct is an authorised dealer for Honeycomb Aeronautical, MOZA Racing and Max Flight Stick, and you can browse our helicopter controls to see what fits your setup. Planning a larger build? Our Dandenong South showroom is open by appointment.
Written by Blake Sterling, Founder, Owner and CEO of Gamer Gear Direct. Blake has been helping Australian sim enthusiasts build their dream racing and flight simulator setups since founding GGD in 2019. When he's not in the Dandenong South showroom, you'll find him behind the wheel in Assetto Corsa Competizione, Forza Horizon and Wreckfest.